Need some head....ers

[PenguinLTZ]

I am goin with Dynatech when I do it

I glanced over those. One, I didn't see any bungs for the pre-cat O2s. Second, the primaries look like they are only tacked in place on the flange. Of course, this is the pictures I can find.

Quite certain they have everything you need. I would contact them before you make the assumption that the o2 sensor bungs aren't there. Jarrod has a set on his.

They are high quality, not just tack welded

 

[CJ Hungus]

The reason I ask is because there is the crappy ebay/Chinese headers that seem to hold up fairly well, but might not have a perfect fit. They usually run around the 300 dollar range. Then there are the top notch, fully stainless, well put together headers like ARH/Stainlessworks/Dynatech. Those will be closer to 700-900 dollar range.

I saw the Stainless works. The only ones I saw were for the 8.1. The ones listed for the 1/2tons were double the price ($1400). I know the LS are all the same, but is there a difference why the ones for the 1/2tons won't fit the HDs?

I would give them a call. I think people have used them on HD's.

 

[ScottyBoy]

I work with a guy with a 03HD with the 6.0 and he mentioned he was looking for headers. I told him about this forum and about Blackbear. He did end up emailing Justin at Blackbear and he told me that Justin suggested Doug Thorley headers for his particular truck. I think he quoted him around $600ish. Not sure if that included shipping or not.
Why don't you send Justin an email and ask him yourself about what headers they sell that will fit on a HD and are in your price range?

 

[Draenor]

I work with a guy with a 03HD with the 6.0 and he mentioned he was looking for headers. I told him about this forum and about Blackbear. He did end up emailing Justin at Blackbear and he told me that Justin suggested Doug Thorley headers for his particular truck. I think he quoted him around $600ish. Not sure if that included shipping or not.
Why don't you send Justin an email and ask him yourself about what headers they sell that will fit on a HD and are in your price range?

I looked at the Thorleys, specifically state non HD.

I already sent Jenna an email, so I see.

 

[JennaBear]

Your email bounced back!

You mentioned that you wanted to keep stock components with the LTs, that will require a ton of modification on your end. An OR Y pipe would be better suited.

We do sell Doug Thorley headers, and just make a large purchase of them. We also like the AEM LTs, and Dynatechs if you want to spend some $$$.

 

[Bigredmariner]

My Dynatech's had pre cat bungs welded in already. I did have to add a second pre-cat bung for my AFR probe though.

 

[Draenor]

Your email bounced back!

You mentioned that you wanted to keep stock components with the LTs, that will require a ton of modification on your end. An OR Y pipe would be better suited.

We do sell Doug Thorley headers, and just make a large purchase of them. We also like the AEM LTs, and Dynatechs if you want to spend some $$$.

Damn the internets....I'll shoot you a pm...

My Dynatech's had pre cat bungs welded in already. I did have to add a second pre-cat bung for my AFR probe though.

Sweet....I'll have to do the same.

 

[Draenor]

How about these?

Is there any negatives to merge the two banks here than at the muffler as the OEM setup? It would save a bit of room than running two sets of pipes.

 

[slims]

I just skeeted in my pants a little.

 

[Draenor]

Deal fell thru with Justin.

Thought about these, before the Dynatechs. I'm not too concerned about the finish as I plan on wrapping them. If I can the same quality of the Dynatechs at half the price, I'm all for it. Its the quality I am worried about. They need to work with a TVS...