New tool thread.

[bubbatrucklover]

Bought a couple of these the other day from Lowes

I like them EZ locks. I JUST discovered them.

Rather then buy a dremel I all ready had a Rotozip (to me semi useless) THEN I bought the flex shaft attachment that turns it into a "dremel".

Only $30 clams, so not bad IMHO.

 

[mr_bots]

All of this air compressor talk got me curious...apparently I know nothing about cfm and was way off on scale.

For nerdy people (like me) I thought I'd share the findings. The main plant air system is a 3000cfm system consisting of a 200hp 993cfm IR, a 100hp 560cfm IR, and two 150hp 826cfm Sullair compressors, a 3000cfm dessicant dryer, and a 6000gal main reciever.

How big is your plant?

Umm...idk really know how to rate it on size. The local site (plant and mine) has about 700 employees and contractors if that helps.

 

[agjake11]

All of this air compressor talk got me curious...apparently I know nothing about cfm and was way off on scale.

For nerdy people (like me) I thought I'd share the findings. The main plant air system is a 3000cfm system consisting of a 200hp 993cfm IR, a 100hp 560cfm IR, and two 150hp 826cfm Sullair compressors, a 3000cfm dessicant dryer, and a 6000gal main reciever.

How big is your plant?

Umm...idk really know how to rate it on size. The local site (plant and mine) has about 700 employees and contractors if that helps.

That's pretty big. Our facility is separation and truck loading for 5000 barrels of oil per day and will have only a few operators onsite and trucks

 

[mr_bots]

All of this air compressor talk got me curious...apparently I know nothing about cfm and was way off on scale.

For nerdy people (like me) I thought I'd share the findings. The main plant air system is a 3000cfm system consisting of a 200hp 993cfm IR, a 100hp 560cfm IR, and two 150hp 826cfm Sullair compressors, a 3000cfm dessicant dryer, and a 6000gal main reciever.

How big is your plant?

Umm...idk really know how to rate it on size. The local site (plant and mine) has about 700 employees and contractors if that helps.

That's pretty big. Our facility is separation and truck loading for 5000 barrels of oil per day and will have only a few operators onsite and trucks

I figured you'd understand barrels per day but we measure in tons per day.

 

[agjake11]

Uh yea that's a lot more haha

 

[tleach17]

Got a new scan tool today. I got it when it was on sale for $285. I love the layout of this unit and all the features.

http://www.matcotools.com/catalog/product/MPS700/OBD-II-AND-ABS-SCAN-TOOL/

This is not my pic but it looks the same.

 

[agjake11]

Nice. You find yourself scanning a lot of different vehicles? I figure I can use the edge for that now.

 

[tleach17]

Yeah. I work on lots of stuff on the side. Plus between the cars I have, My folks have and my close friends it will get put to good use.

 

[Stumpuller6.5]

Just got one of these. Damn tough little bastard, some serious torque!

My last skil and mastercraft professional units all had battery issues and it cost too much just to buy a new battery.

Comes with 2 batterys, charger and carry case, has a 5 year warranty on the drill and 3 years on charger and batteries!

 

[RedRider]

That's cool. Might have to look into that. We always end up buying a new drill when the batteries go on our DeWalts.