What Did You Do To Your Truck Today? v2.0

[NMRam]

Ordered a new tune so I can burn some more fuel since it’s so cheap and abundant now…

 

[OldCracker29]

I had the TPMS sensors replaced a few days ago and I changed the oil in it yesterday.

 

[Jeanpaul]

I'm looking for recommendations on the brand of dually wheels I should acquire for my 2012 Ram 2500. Thank you in advance to those who are willing to provide their ideas!

 

[OldCracker29]

Finally got the rear brakes done. I do believe they were the original rotors on the pig. Three of the four slide pins on the caliper were a m/fer to get out.

 

[kennythewelder]

Well, let's see, after I rebuilt the rear end in February, the trans blew up 1-1/2 weeks later, so a transmission rebuild, that lasted about 2 months, then I blew that up again, but they made it good at the transmission shop. So a 2ed rebuild. It's been good since. They had the performance and pressures turned up to much. The Corvette servos do shift good though, and the HD master rebuild kit should hold up too. Then I started on the front end last month. I had to replace the idler arm, it's mount, the pitman arm, and tighten down the wheel bearings. I had it aligned at a shop where I had it done almost 3 years ago. I had a 3 year warranty on the alignment. So I got new tires. Well I knew the alignment wasn't rite, so I go back to the alignment shop, and they give me BS. I leave there, and go to where I got my tires, and had them align it. Now it's rite, finally. Put a set of Hankook kinergy tires. A 70,000 mile tire. So far, so good. They ride a lot better than the Milestar street steels I had, and I only got 15,000 miles out of those tires. Hopefully I can get a lot more miles out of these.

 

[OldCracker29]

Well, let's see, after I rebuilt the rear end in February, the trans blew up 1-1/2 weeks later, so a transmission rebuild, that lasted about 2 months, then I blew that up again, but they made it good at the transmission shop. So a 2ed rebuild. It's been good since. They had the performance and pressures turned up to much. The Corvette servos do shift good though, and the HD master rebuild kit should hold up too. Then I started on the front end last month. I had to replace the idler arm, it's mount, the pitman arm, and tighten down the wheel bearings. I had it aligned at a shop where I had it done almost 3 years ago. I had a 3 year warranty on the alignment. So I got new tires. Well I knew the alignment wasn't rite, so I go back to the alignment shop, and they give me BS. I leave there, and go to where I got my tires, and had them align it. Now it's rite, finally. Put a set of Hankook kinergy tires. A 70,000 mile tire. So far, so good. They ride a lot better than the Milestar street steels I had, and I only got 15,000 miles out of those tires. Hopefully I can get a lot more miles out of these. View attachment 7484 View attachment 7485

I need to get some front end work done on mine as well.

 

[Black02Silverado]

Finally got the rear brakes done. I do believe they were the original rotors on the pig. Three of the four slide pins on the caliper were a m/fer to get out.

How many miles on them?

 

[Black02Silverado]

Well, let's see, after I rebuilt the rear end in February, the trans blew up 1-1/2 weeks later, so a transmission rebuild, that lasted about 2 months, then I blew that up again, but they made it good at the transmission shop. So a 2ed rebuild. It's been good since. They had the performance and pressures turned up to much. The Corvette servos do shift good though, and the HD master rebuild kit should hold up too. Then I started on the front end last month. I had to replace the idler arm, it's mount, the pitman arm, and tighten down the wheel bearings. I had it aligned at a shop where I had it done almost 3 years ago. I had a 3 year warranty on the alignment. So I got new tires. Well I knew the alignment wasn't rite, so I go back to the alignment shop, and they give me BS. I leave there, and go to where I got my tires, and had them align it. Now it's rite, finally. Put a set of Hankook kinergy tires. A 70,000 mile tire. So far, so good. They ride a lot better than the Milestar street steels I had, and I only got 15,000 miles out of those tires. Hopefully I can get a lot more miles out of these. View attachment 7484 View attachment 7485

Man, it seems harder to find quality work anymore. At least you got it straightened out.

 

[OldCracker29]

How many miles on them?

Almost 237K on them.

 

[Black02Silverado]

Almost 237K on them.

At least you got your moneys worth.